Image 1 of 1
A5 - Badab War Astral Claws Maelstrom Warders Waterslide Transfers
A5 Custom Printed Transfer Sheet
There may also be a slight white offset under the design, this is uncommon but can still happen so please be aware of this as well.
These are more expensive than my usual sheets as I am using a special printer with another supplier that can make transfers to go over any colour and can also be printed in white or metallics, my regular sheets for dark over light I don't use this printer for, this process also takes a bit longer to do so please be patient.
Please note there is a chance some icons on the side of the sheet get cut off during printing, it is not an exact science and I have no control over the process, it is unlikely that it will happen but sometimes it does but there is a lot of icons on the sheet anyway.
Due to this unfortunate occasional error and since I can't fix it myself I will post these sheets as they come like this since the other icons are still usable, I will not accept returns or cancellations if this happens and you haven't read this or allow negative feedback, if I was printing them myself I would be happy to help fix it.
Approximate measurements of the icons are;
Tiger Heads
6mm
8mm
10mm
15mm
Tyrants Claw + Warders Icon.
4mm
6mm
10mm
Please note these are made to order and have to be printed and sealed which can take a while of course, these are not pre-made ready to ship so please be patient.
Directions for use
1) Gloss varnish the area of the miniature you’d like to apply the transfer to first.
2) Wait for the gloss to dy.
3) Cut around the icon as close as possible to fit on the miniature area, these are not pre-cut.
4) Soak the decal in water for a few seconds, if you over soak the transfer the ink may bleed.
5) Gently lift off the transfer with a brush and apply it onto the model
6) Position the decal how you want it on the model
7) Allow it to fully dry
8) Apply thin coats of decal softener like Microsol / Set letting it dry in-between coats until the edge is flat and no bubbles are visible.
9) Seal in the finished model with a varnish of your choic
A5 Custom Printed Transfer Sheet
There may also be a slight white offset under the design, this is uncommon but can still happen so please be aware of this as well.
These are more expensive than my usual sheets as I am using a special printer with another supplier that can make transfers to go over any colour and can also be printed in white or metallics, my regular sheets for dark over light I don't use this printer for, this process also takes a bit longer to do so please be patient.
Please note there is a chance some icons on the side of the sheet get cut off during printing, it is not an exact science and I have no control over the process, it is unlikely that it will happen but sometimes it does but there is a lot of icons on the sheet anyway.
Due to this unfortunate occasional error and since I can't fix it myself I will post these sheets as they come like this since the other icons are still usable, I will not accept returns or cancellations if this happens and you haven't read this or allow negative feedback, if I was printing them myself I would be happy to help fix it.
Approximate measurements of the icons are;
Tiger Heads
6mm
8mm
10mm
15mm
Tyrants Claw + Warders Icon.
4mm
6mm
10mm
Please note these are made to order and have to be printed and sealed which can take a while of course, these are not pre-made ready to ship so please be patient.
Directions for use
1) Gloss varnish the area of the miniature you’d like to apply the transfer to first.
2) Wait for the gloss to dy.
3) Cut around the icon as close as possible to fit on the miniature area, these are not pre-cut.
4) Soak the decal in water for a few seconds, if you over soak the transfer the ink may bleed.
5) Gently lift off the transfer with a brush and apply it onto the model
6) Position the decal how you want it on the model
7) Allow it to fully dry
8) Apply thin coats of decal softener like Microsol / Set letting it dry in-between coats until the edge is flat and no bubbles are visible.
9) Seal in the finished model with a varnish of your choic