These are also not pre-cut icons like in a GW transfer box, you have to cut around the icon yourself on the clear film part so there is an edge to work with.
These are printed using a Laser printed and may take quite a while to be ready due to how time consuming the process is and other orders before yours. I do not do rush orders and these are not the same as the sheet you get in a GW box, decal printing is not an exact process and there may be a few differences from the mock design such as the colour being a bit brighter, white being slightly transparent and also sometimes a white offset to the icons, I can't control this and they are minor issues so please bear in mind before you purchase.
Please read before purchase, I will not accept any cancellations for 'Won't arrive on time or changed mind on these items' If you have the put the wrong address in as well please just let me know where you'd like it sending instead of putting in a cancellation as these affect my seller ratings.
There may also be a slight white offset under the design, this is uncommon but can still happen so please be aware of this as well.
The icons for these were measured for Wargames Atlantic and FireForge Deus Vult Miniatures, please check your models before purchasing this sheet to make sure they will fit what you are using, these have been made for use on Tabards, Surcoats, Shields, Capes and Banners these are also suitable for Games Workshop Space Marines and Bretonnian Knights
These are inspired by the Falcon Knights from LEGO Castle, I am not affiliated with LEGO
Icon sizes are
3mm
6mm
10mm
15mm
Please note there is a chance some icons on the side of the sheet get cut off during printing, it is not an exact science and I have no control over the process, it is unlikely that it will happen but sometimes it does but there is a lot of icons on the sheet anyway.
Due to this unfortunate occasional error and since I can't fix it myself I will post these sheets as they come like this since the other icons are still usable, I will not accept returns or cancellations if this happens and you haven't read this or allow negative feedback, if I was printing them myself I would be happy to help fix it.
Message me if you'd like more than more than one special sheet printed as I can do bulk deals!
These were printed on clear decal paper and you need to cut around the icon as close as possible to get them onto the shoulders otherwise the film will be too big I also recommend using the Microsol and Microset method
Please note that not all detail may be printed on smaller icons such as holes on eyes or anything similar due to how toner ink works, they will still of course give the effect of the icon from afar and on a shoulder pad anyway.
Recommended Directions for use
1: Gloss Varnish the model or the area you would like to apply the transfer ( I use either Army Painter Gloss Varnish via brush or Hycote Clear Lacquer for spray)
2: Wait for the Varnish to dry
3: Cut around the decal as close as you can giving your self an edge around the icon (Do not cut the icon) these are not pre cut like regular transfers.
4: Apply a thincoat of Microset to the area of the model you will apply the decal
5: Soak the transfer in some lukewarm water for a few seconds
6: Slide the icon off the paper and onto the model
7: Position the decal onto the miniature where you'd like it
8: Carefully apply some Microset if you want to
9: Wait for the decal to full dry
10: Use thin coats of Microsol with a Q-Tip or old brush, letting it dry in-between coats until the edge is gone
11: Varnish the model with your choice of finish
These are also not pre-cut icons like in a GW transfer box, you have to cut around the icon yourself on the clear film part so there is an edge to work with.
These are printed using a Laser printed and may take quite a while to be ready due to how time consuming the process is and other orders before yours. I do not do rush orders and these are not the same as the sheet you get in a GW box, decal printing is not an exact process and there may be a few differences from the mock design such as the colour being a bit brighter, white being slightly transparent and also sometimes a white offset to the icons, I can't control this and they are minor issues so please bear in mind before you purchase.
Please read before purchase, I will not accept any cancellations for 'Won't arrive on time or changed mind on these items' If you have the put the wrong address in as well please just let me know where you'd like it sending instead of putting in a cancellation as these affect my seller ratings.
There may also be a slight white offset under the design, this is uncommon but can still happen so please be aware of this as well.
The icons for these were measured for Wargames Atlantic and FireForge Deus Vult Miniatures, please check your models before purchasing this sheet to make sure they will fit what you are using, these have been made for use on Tabards, Surcoats, Shields, Capes and Banners these are also suitable for Games Workshop Space Marines and Bretonnian Knights
These are inspired by the Falcon Knights from LEGO Castle, I am not affiliated with LEGO
Icon sizes are
3mm
6mm
10mm
15mm
Please note there is a chance some icons on the side of the sheet get cut off during printing, it is not an exact science and I have no control over the process, it is unlikely that it will happen but sometimes it does but there is a lot of icons on the sheet anyway.
Due to this unfortunate occasional error and since I can't fix it myself I will post these sheets as they come like this since the other icons are still usable, I will not accept returns or cancellations if this happens and you haven't read this or allow negative feedback, if I was printing them myself I would be happy to help fix it.
Message me if you'd like more than more than one special sheet printed as I can do bulk deals!
These were printed on clear decal paper and you need to cut around the icon as close as possible to get them onto the shoulders otherwise the film will be too big I also recommend using the Microsol and Microset method
Please note that not all detail may be printed on smaller icons such as holes on eyes or anything similar due to how toner ink works, they will still of course give the effect of the icon from afar and on a shoulder pad anyway.
Recommended Directions for use
1: Gloss Varnish the model or the area you would like to apply the transfer ( I use either Army Painter Gloss Varnish via brush or Hycote Clear Lacquer for spray)
2: Wait for the Varnish to dry
3: Cut around the decal as close as you can giving your self an edge around the icon (Do not cut the icon) these are not pre cut like regular transfers.
4: Apply a thincoat of Microset to the area of the model you will apply the decal
5: Soak the transfer in some lukewarm water for a few seconds
6: Slide the icon off the paper and onto the model
7: Position the decal onto the miniature where you'd like it
8: Carefully apply some Microset if you want to
9: Wait for the decal to full dry
10: Use thin coats of Microsol with a Q-Tip or old brush, letting it dry in-between coats until the edge is gone
11: Varnish the model with your choice of finish
